Solid all-round for its segment
The JA Solar M2 series consists of modules designed for high energy yield in real-world conditions, where factors such as shading, different mounting angles, and limited roof space are important. The use of half-cut technology reduces internal losses and helps maintain stable performance even when part of the panel is exposed to less light. Monocrystalline PERC cells and multi-busbar connections (MBB) support efficient current collection and minimize the impact of micro-cracks on long-term performance.
In practice, the M2 series solves common problems associated with residential and commercial solar installations - it improves tolerance to shading, simplifies string design, and provides predictable yields during transitional seasons. It is a good choice for single-family homes, small businesses, and rooftop installations with limited load-bearing capacity, where a lightweight design and simpler installation are important. Compared to the competition, the series stands out due to its consistent 182 mm platform, which is meticulously designed for durability and stability over time.
Ranking
Signals from the data
Residential, commercial and shaded-installations.
Splitting cells in half reduces internal resistive losses by approximately 50%, while multi-busbar (MBB) interconnects lower the impact of microcracks and improve partial-shading tolerance. In practice, this results in more stable string output under the non-uniform irradiance typical of pitched rooftops.
JA Solar is listed on the BNEF Tier-1 Q1 2026 ranking with annual production capacity exceeding 80 GW. Tier-1 bankable status means that lenders accept these modules as project collateral and that the 25-year linear power warranty is backed by the manufacturer's verified financial standing.
A broad power range allows system designers to match module output to varying roof sizes and load requirements without accepting oversized wattage bins, and enables precise string sizing to minimize MPPT balancing losses.
Peak efficiency of 21.2% ties with MY Solar M2 (21.2%) and exceeds both Solarwatt Panel vision GM 3.0 pure (20.7%) and KB Solar KBS-MONO-BF (20.9%) from the peer-comparable set - placing this P-type PERC series at the top of the reference group.
The M2 series went end-of-life around 2021. This eliminates access to replacement modules for warranty claims, creates a visual and electrical mismatch risk if the array is later expanded, and limits ongoing technical support - a material operational risk for installations expected to run 25+ years.
P-type PERC cells carry a temperature coefficient of Pmax ≈ -0.35%/°C versus -0.30%/°C for TOPCon modules, which captured roughly 65% of global production in 2024. Annual PERC degradation runs 0.45-0.55% versus 0.30-0.40% for TOPCon; over the 25-year warranty horizon, the cumulative energy yield gap can reach 3-7 percentage points in favor of modern TOPCon alternatives.
- At 19.4% efficiency, this panel is on par with typical PERC 0-400W modules
- At 193.6 W/m² power density, roof space requirements are typical for PERC 0-400W panels
- Temperature coefficient of -0.37%/°C matches the PERC 0-400W median
- At 18.5 kg, this panel is 2.0 kg lighter than PERC 0-400W median (20.5 kg) - easier handling during installation
- Ranked #12774 out of 14005 panels for efficiency in the database
Specifications
Simulations
Degradation from this panel's own datasheet figures. No inverter, soiling or shading losses.
Found 182 panels of the same or similar size to this one, within ±10 mm. See them here Found 218 panels of the same or similar size to this one, within ±25 mm. See them here Found 379 panels of the same or similar size to this one, within ±50 mm. See them here Found 472 panels of the same or similar size to this one, within ±100 mm. See them here
About the M2 series series
These answers cover the whole series. Where a figure differs, the specification above is this module's own.