Middle of its segment, modest efficiency
The HT-SAAE HT40-18X(ND)-F series was designed to maximize energy yield where long-term, reliable performance over years matters just as much as a good result in laboratory conditions. The use of N-type cells in TOPCon technology translates to lower light-induced losses and better predictability of production throughout the entire system's lifetime. Furthermore, the double glass construction improves resistance to moisture, micro-cracking, and accelerated aging, genuinely reducing the risk of power degradation in harsh climates.
Another advantage of this series is half-cut technology, which minimizes resistive losses and increases tolerance to partial shading - crucial for installations with chimneys, roof penetrations, or during east-west mounting. In practice, this means higher yield in low light conditions and a more consistent production profile throughout the day. This is an excellent choice for both residential and commercial installations, where lower energy costs over time and high reliability are prioritized over compromises typical for P-type panels.
Ranking
Signals from the data
Residential, commercial and shaded-installations.
Tight roof space and roofs where every square metre has to count.
Bottom 1% of the TOPCon 300-350 W segment, against a median of 15.01%. Ranked 13,990th in the whole database.
Bottom 1% of the TOPCon 300-350 W segment, against a median of 150.1. Ranked 13,980th in the whole database.
N-type TOPCon technology eliminates Light Induced Degradation (LID) that is characteristic of older P-type PERC cells. The bifacial design captures additional energy from the rear side of the module — up to 20–30% extra yield under favorable albedo conditions according to manufacturer data — meaningfully increasing annual system output without adding more panels.
HT-SAAE provides a full 30-year warranty covering both product integrity and power output for this series, whereas peer comparables in the segment — JA Solar Monocrystalline80 and Jinko Solar 72 Series — standardly offer a 25-year power warranty. The extended warranty horizon reduces investment risk when calculating LCOE (levelized cost of energy) for commercial and prosumer installations.
The frameless double-glass construction eliminates the typical aluminum frame corrosion points and mitigates the risk of PID (Potential Induced Degradation) by fully encapsulating the cells between two glass panes. In practice, this translates to a lower degradation rate in humid climates and in ballasted rooftop mounting systems on flat roofs.
HT-SAAE is listed on the BNEF Tier 1 module manufacturers list (confirmed quarterly through H1 2026), establishing project bankability — a prerequisite required by financing institutions for commercial and utility-scale installations. The company has been operating since 1998 (27 years), significantly reducing the risk of warranty service discontinuation over the 30-year warranty horizon.
Splitting cells in half reduces operating current by 50%, which lowers resistive losses (I²R) and improves module performance under partial shading. For rooftops with chimneys, dormers, or east–west orientations, this delivers a measurable increase in energy production during morning and afternoon hours compared to conventional full-cell modules.
The HT40-18X(ND)-F module efficiency of 12–12.8% is significantly lower than all listed peer comparables: JA Solar Monocrystalline80 reaches 23.15%, Waaree ARKA Series 19.81%, and even the Jinko Solar 72 Series Polycrystalline achieves 17%. This stems from the module's large physical footprint (~2285×1134 mm, approximately 2.59 m²) combined with a relatively low power rating of 310–330 Wp and a low active cell coverage ratio (~51%). In practical terms, achieving 1 kWp of installed capacity requires approximately 1.85× more roof area than equivalent-peak-power JA Solar panels.
- Module efficiency of 12.0% is 4.0pp below average for TOPCon 0-400W panels (median: 16.0%)
- 120.0 W/m² power density is 39.8 W/m² below TOPCon 0-400W median (159.8 W/m²) - requires larger installation area
- At -0.31%/°C, loses 0.02pp more power per degree than TOPCon 0-400W median (-0.29%/°C)
- At 32.5 kg, this panel is 9.0 kg heavier than the TOPCon 0-400W median (23.5 kg) - more demanding for installation crews
- Bifaciality factor of 74% can add 4-11% extra yield with reflective mounting surface
Specifications
Simulations
Degradation from this panel's own datasheet figures. No inverter, soiling or shading losses.
Model: bifaciality × albedo × 0.6 view factor. A first-order estimate, not a yield simulation.
Alternatives
Found 2326 panels of the same or similar size to this one, within ±10 mm. See them here Found 2368 panels of the same or similar size to this one, within ±25 mm. See them here Found 2382 panels of the same or similar size to this one, within ±50 mm. See them here Found 2547 panels of the same or similar size to this one, within ±100 mm. See them here